How To Stick LED Strip Lights On Wall Without Damaging Paint

When it comes to decorating your home, LED strip lights are the most economical and convenient among all of your choices. LED lights can be easily applicable & replaceable as well as consume less energy compared to some other more permanent choices. 

However, LED lights can look jarring if you just place them in the open. There is a certain art to setting up LED strip lights so that they look really beautiful and aesthetic.

However, there is a catch, sometimes your wall might be damaged due to the adhesive or hook used in setting up the LED.In this case, you have to know how to stick LED strip lights on wall without damaging paint. 

How To Stick LED Strip Lights On Wall Without Damaging Paint

LED lights to come pre-attached with a certain type of adhesive or hook. It is important to know how to properly set it up. Before we start discussing how to stick LED strip lights on wall without damaging paint, we need some equipment. 

  • A strong adhesive or glue
  •  Measuring Tape
  •  Exacto Knife
  • Double-sided tape
  • Scissors
  • Alcohol

It may seem that adhesive or tape will tear off the paint. However, not all kinds of tape or adhesive are strong enough to tear off the paint of the walls. These kinds of adhesives and tapes are useful in setting up LED strips.

How to Stick Led Strip Lights on Wall without Damaging Paint Step by Step Guide

The following guide will help you find your way around the equipment and set up LED strips without damaging paint. Be sure to understand each step before you start and contact an expert if you are unsure of how to proceed.

Step 1: Take Measurements

The first step is to take actual measurements. Visualize where you want to place the actual LED strips. Use a ruler or a measuring tape to take exact measurements and calculate how many LED strip lights you will be needing.

It is important to take exact measurements otherwise you will need to adjust your design accordingly.

Measurement of Wall

Step 2: Cut to Size

The next step is to carefully piece together your visualized shape. Cut the LED strips to the proper size with a sharp knife or scissors. The LED strips usually come with marked lines. These lines are where you should be making your cuts. 

Cuts outside of this mark may damage the circuit. You also might need to solder new connectors cables if you cut your strips accordingly.

Step 3: Preparing the Surface

LED strips usually come with their version of an adhesive. It is usually behind a sealed cover. The LED strips are best placed on flat surfaces. The adhesive sticks nicely on flat surfaces so cutting them into exact pieces helps them to easily stick on the walls.

Download Our FREE Strip Light Cheat Sheet

This cheat sheet will help you pick the perfect light strip set up with zero guessing!

LED Light Strip Cheat Sheet

You have to make sure the adhesive’s contact is limited to the surface you are attaching it to. Otherwise, the adhesive will stick strongly to the wall and cause damage to the paint. To prevent this, you can use a wet cloth with water or alcohol and brush off the excess adhesive from the back of the LED strip. Dry it off with another cloth.

Step 4: Peel Off the Adhesive Backing

If your LED strips have the pre-applied backing remove the wrap and apply the LED strip in your desired structure. If your LED strips do not have an applied adhesive, use external glue or tape with minimal surface area.

Step 5: Align and Press

After applying the adhesive or peeling off the wrap, apply the strips in your desired measurements. Continue placing the strips in your predetermined design. Make sure to place the LED strips in locations that the strips themselves don’t stick out but the light will be sufficient.

Stick LED strip Lights On Wall

Step 6: Turn On the Lights

The final step is to connect the wiring and finish the circuit. See that the lighting is how you imagined it. Peel off the LED strips if you think that the lighting is not how you want it. Remember to reapply adhesive in minimal amounts so that the walls are not at risk of being damaged.

This is how to stick LED strip lights on wall without damaging paint. The trick is to apply minimal adhesive or glue to the back of the LED strips. This allows the strip to both be solidly in place but weak enough to peel off without damaging the walls

Do Led Strip Lights Ruin Paint?

LED strip lights can ruin paint off walls. The strong glue that an LED strip uses will stick to the walls and come off with paint if it is pulled straight up. Instead, you have to use heating to weaken the adhesive so that it peels off easily. 

Moreover, you can use less glue on the back of the LED strips to make sure it is easily peelable as well.

Do Led Strip Lights Ruin Wood?

Wood is a flammable material. With enough heat, any wooden products are at risk of getting ignited. However, LED strip lights are not powerful enough to be able to ignite the wood. 

They may cause the material to get warm, but significant damage is very rare. Still, it is better to simulate the environment just to make sure.

How to Remove Led Lights Safely from A Surface?

At first, you have to know how to stick LED strip lights on wall without damaging paint. However, if you have applied LED strips, you will need to apply heat to the adhesive after turning off the power. 

The glue will loosen up. While heated, use your hands to slowly peel off the LED strip from the wall. This is how you can safely remove LED lights from a surface.

Frequently Asked Question

How to Prevent Led Strips from Falling Off?

The adhesive must be preserved so that the LED light does not fall off. If you know how to stick LED strip lights on wall without damaging paint, you should know that your strips have little adhesive. So, you have to prevent it from being close to heat sources. 

Also, make sure no part of the LED strip is facing towards its glue. This will loosen the strip and it will fall off.

Can I Unstick and Then Re-Stick My Le Ds?

Yes, the adhesive on the back of an LED strip is usually reusable. So, you can easily unstick and re-stick the LED. Moreover, you can apply your adhesive in minimal amounts if the previous one becomes unusable.

Can I use super glue to attach LED lights to any surface?

Yes, you can use super glue to attach the strips to any surface. However, super glue is extremely strong and will damage your walls. Avoid using super glue if you think about replacing the LED and do not want to damage your walls.

Conclusion

LED strip lights are versatile in the sense that they can be easily used to decorate your room. They can emit different arrays of lights and create an aesthetic scene in your home. 

Moreover, they are more economical than other lights. LED strip lights are easy to remove as well. For that, you need to know how to stick LED strip lights on wall without damaging the paint. 

Using limited adhesive will help you in unsticking the LED strip without damaging your walls. As such, you can easily restructure the LED to the heart’s content and not worry about permanent damage to your forever home!

Related Articles…

How To Blow A Hole In A Light Bulb

A light bulb is an everyday object that you don’t really think twice about. It is made of a glass container with a…

How To Install Can Lights in A Drop Ceiling

A drop ceiling, also called a false ceiling or second ceiling is a secondary covering that is suspended under the…

How To Remove Led Strip Lights Without Damaging Paint

LED strips are very useful and very convenient to use as well. If you fit an LED light strip nicely, it can go under the radar…

How To Install Toe Kick Lighting

All light lovers must know how to install toe kick lighting as it is a reliable technique to create artificial lighting while…

How To Reset A Merkury Smart Bulb

Smart bulbs are a blessing of the modern age and just a few decades ago people would not have imagined the idea of…